Holgamods Day-Lite 4x5 Sheet Film Processing Tubes
since: 2018/03/28
update: 2018/07/25
reference:
1. ebay: Holgamods Day-Lite 4x5 Sheet Film Processing Tubes
2. youtube: HOLGAMODS 4x5 Daylight Processing Tubes
3. Film Tubes
4. 1. Using the 8x10 BTZS Film Tubes - YouTube
5. 2. How to Use the BTZS 4x5 Film Tube Kit - Part 1 - YouTube
---------------------------------------------------------------------------
Instructions:
1. Bring your exposed film into your dark room, closet, room without windows, etc.
將曝光後的膠片放入黑暗的房間，衣櫃，沒有窗戶的房間等
2. Turn the light off.
關掉這盞燈
3. Separate "Twist and Pull" the "Light Baffle" section from the bottom "Film loaded here" section.
將底部的“電影放在這裡”部分的“輕拉環”部分分開“扭曲和拉動”部分
4. Curl your film into the bottom tube, emulsion side toward center and in Portrait orientation.
將您的膠片捲曲到底部管中，乳膠面朝向中心並以縱向定位
5. Replace the light Baffle section back on the film section.
將薄擋板部分重新放回膠片部分
6. Turn the lights on.
打開燈
7. Twist off the top cap, fill tube with approximately 6 ounces of developer.
擰下頂蓋，用約6盎司(約 180 cc)的顯影劑填充管 (p.s. 1盎司約 30cc)
8. Continue processing as you normally would with any Day Light Processing Tank.
像任何日光處理罐一樣繼續處理
9. After you film has soaked the fix for a few minutes, you'll be able to open the tube and
pull the film from the tube. Then float it in a tray or small tupperware bowl to have
the fix to come in contact with the back side of the film.
膠片浸泡了幾分鐘後，你就可以打開膠管了, 從管中拉出薄膜。 然後將其浮在托盤或小特百惠碗中, 該修補程序與電影的背面接觸.
10. While your film is fixing, dry the tube and load another sheet.
在您的膠片正在固定時，將管道乾燥並裝入另一張紙
---------------------------------------------------------------------------
藥劑容量
1. 預浸: 水 200ml
2. 顯影液(HC-110 B -> 1:31): 藥水 6ml 水 194ml
6:00 min at 20℃
3. 停影(冰醋酸 -> 16:1000): 藥水 1/3瓶蓋(3.2 ml) 水 200ml
4. 定影(Fixer -> 1:4): 藥水 40ml 水 160ml
5. 預洗: 水 200ml
6. 海波清潔:(1:4): 藥水 40ml 水 160ml
7. 水洗: 大量
8. 去水漬: 1/3瓶蓋 ( 1000ml 水加入 5cc Kodak Photo-flo 藥水)
update: 2018/07/25
reference:
1. ebay: Holgamods Day-Lite 4x5 Sheet Film Processing Tubes
2. youtube: HOLGAMODS 4x5 Daylight Processing Tubes
3. Film Tubes
4. 1. Using the 8x10 BTZS Film Tubes - YouTube
5. 2. How to Use the BTZS 4x5 Film Tube Kit - Part 1 - YouTube
Instructions:
1. Bring your exposed film into your dark room, closet, room without windows, etc.
將曝光後的膠片放入黑暗的房間，衣櫃，沒有窗戶的房間等
2. Turn the light off.
關掉這盞燈
3. Separate "Twist and Pull" the "Light Baffle" section from the bottom "Film loaded here" section.
將底部的“電影放在這裡”部分的“輕拉環”部分分開“扭曲和拉動”部分
4. Curl your film into the bottom tube, emulsion side toward center and in Portrait orientation.
將您的膠片捲曲到底部管中，乳膠面朝向中心並以縱向定位
5. Replace the light Baffle section back on the film section.
將薄擋板部分重新放回膠片部分
6. Turn the lights on.
打開燈
7. Twist off the top cap, fill tube with approximately 6 ounces of developer.
擰下頂蓋，用約6盎司(約 180 cc)的顯影劑填充管 (p.s. 1盎司約 30cc)
8. Continue processing as you normally would with any Day Light Processing Tank.
像任何日光處理罐一樣繼續處理
9. After you film has soaked the fix for a few minutes, you'll be able to open the tube and
pull the film from the tube. Then float it in a tray or small tupperware bowl to have
the fix to come in contact with the back side of the film.
膠片浸泡了幾分鐘後，你就可以打開膠管了, 從管中拉出薄膜。 然後將其浮在托盤或小特百惠碗中, 該修補程序與電影的背面接觸.
10. While your film is fixing, dry the tube and load another sheet.
在您的膠片正在固定時，將管道乾燥並裝入另一張紙
---------------------------------------------------------------------------
藥劑容量
1. 預浸: 水 200ml
2. 顯影液(HC-110 B -> 1:31): 藥水 6ml 水 194ml
6:00 min at 20℃
3. 停影(冰醋酸 -> 16:1000): 藥水 1/3瓶蓋(3.2 ml) 水 200ml
4. 定影(Fixer -> 1:4): 藥水 40ml 水 160ml
5. 預洗: 水 200ml
6. 海波清潔:(1:4): 藥水 40ml 水 160ml
7. 水洗: 大量
8. 去水漬: 1/3瓶蓋 ( 1000ml 水加入 5cc Kodak Photo-flo 藥水)
留言
張貼留言