Developer: Kodak HC-110
since: 2018/06/17
update: 2018/06/18
reference:
1. KODAK PROFESSIONAL HC-110 Developer - Kodak Alaris
2. Kodak Professional HC-110 Developer
3. Kodak HC-110 Developer - Unofficial Resource Page
4. Kodak HC-110显影液非官方全面指南 - 黑白摄影
5. 生活就是吃飯、玩耍和磨爪: Kodak HC-110 developer (顯影液)
---------------------------------------------------------------------------
---------------------------------------------------------------------------
PREPARING WORKING SOLUTIONS
準備工作解決方案
You can prepare HC-110 Developer working solutions by diluting stock solution or concentrate. (Both mixing methods provide the same photographic characteristics.)
To prepare stock solution, dilute one part concentrate with three parts water.
To prepare working solutions, dilute stock solution or concentrate according to the
following tables. Mix either stock or working solutions at a temperature between
10 and 32°C (50 and 90°F).
您可以通過稀釋原液或濃縮液來準備HC-110開發人員的工作解決方案。 （兩種混合方法都提供相同的照相特性。）
準備原液時，用三份水稀釋一份濃縮液。 要準備工作溶液，請根據下表稀釋原液或濃縮液。 在10至32°C（50至90°F）的溫度下混合原液或工作溶液。
建議:
1. 因為濃縮液具黏稠性，倒出時速度要慢以避免氣泡的產生，如有氣泡，應靜置待其消失
再進行容量判讀。
2. 濃縮液如有沾附在量測容器壁上應等待其流下。
3. 如果要量測較少量的濃縮液，量測工具刻度要精準到 0.5 ml (可用針筒較易量取)。
4. 用清水沖洗裝濃縮液的容器至少五次，並將沖洗後的液體倒入稀釋液中，
確保濃縮液無殘留容器壁面。
5. 稀釋時攪拌數分鐘，確保濃縮液完全溶解。
---------------------------------------------------------------------------
DEVELOPMENT TIMES
開發時間
If film is properly exposed, the times in the following tables should produce negatives
with contrast suitable for printing with a diffusion enlarger (or by contact) on a normal-
contrast black-and-white paper. If printing negatives with a condenser enlarger,
decrease the development time by approximately 30 percent to produce lower contrast.
For critical applications, run tests to determine the best development time. If your negatives
are consistently too dense or high in contrast, decrease the development time; if they’re
too thin or low in contrast, increase the development time.The following tables offer
starting-point recommendations. Adjust as needed.
如果膠片曝光正確，下表中的時間應該產生負片，對比度適合用普通對比度黑白紙上的擴散放大器（或接觸片）進行打印。 如果使用聚光器放大器打印底片，請將顯影時間縮短約30％，以降低對比度。
對於關鍵應用程序，運行測試以確定最佳開發時間。 如果您的負面因素始終過於密集或高對比度，請減少開發時間; 如果它們太薄或太低，則會增加開發時間。以下表格提供了起點
建議。 根據需要調整。
---------------------------------------------------------------------------
update: 2018/06/18
reference:
1. KODAK PROFESSIONAL HC-110 Developer - Kodak Alaris
2. Kodak Professional HC-110 Developer
3. Kodak HC-110 Developer - Unofficial Resource Page
4. Kodak HC-110显影液非官方全面指南 - 黑白摄影
5. 生活就是吃飯、玩耍和磨爪: Kodak HC-110 developer (顯影液)
PREPARING WORKING SOLUTIONS
準備工作解決方案
You can prepare HC-110 Developer working solutions by diluting stock solution or concentrate. (Both mixing methods provide the same photographic characteristics.)
To prepare stock solution, dilute one part concentrate with three parts water.
To prepare working solutions, dilute stock solution or concentrate according to the
following tables. Mix either stock or working solutions at a temperature between
10 and 32°C (50 and 90°F).
您可以通過稀釋原液或濃縮液來準備HC-110開發人員的工作解決方案。 （兩種混合方法都提供相同的照相特性。）
準備原液時，用三份水稀釋一份濃縮液。 要準備工作溶液，請根據下表稀釋原液或濃縮液。 在10至32°C（50至90°F）的溫度下混合原液或工作溶液。
建議:
1. 因為濃縮液具黏稠性，倒出時速度要慢以避免氣泡的產生，如有氣泡，應靜置待其消失
再進行容量判讀。
2. 濃縮液如有沾附在量測容器壁上應等待其流下。
3. 如果要量測較少量的濃縮液，量測工具刻度要精準到 0.5 ml (可用針筒較易量取)。
4. 用清水沖洗裝濃縮液的容器至少五次，並將沖洗後的液體倒入稀釋液中，
確保濃縮液無殘留容器壁面。
5. 稀釋時攪拌數分鐘，確保濃縮液完全溶解。
---------------------------------------------------------------------------
DEVELOPMENT TIMES
開發時間
If film is properly exposed, the times in the following tables should produce negatives
with contrast suitable for printing with a diffusion enlarger (or by contact) on a normal-
contrast black-and-white paper. If printing negatives with a condenser enlarger,
decrease the development time by approximately 30 percent to produce lower contrast.
For critical applications, run tests to determine the best development time. If your negatives
are consistently too dense or high in contrast, decrease the development time; if they’re
too thin or low in contrast, increase the development time.The following tables offer
starting-point recommendations. Adjust as needed.
如果膠片曝光正確，下表中的時間應該產生負片，對比度適合用普通對比度黑白紙上的擴散放大器（或接觸片）進行打印。 如果使用聚光器放大器打印底片，請將顯影時間縮短約30％，以降低對比度。
對於關鍵應用程序，運行測試以確定最佳開發時間。 如果您的負面因素始終過於密集或高對比度，請減少開發時間; 如果它們太薄或太低，則會增加開發時間。以下表格提供了起點
建議。 根據需要調整。
留言
張貼留言